Digital Watchdog DWC-MV421D Instrukcja Obsługi Strona 1

Before installing and using the MEGAPIX Camera, please read this manual carefully. Be sure to keep it handy for future reference. 07262012 IP

NETWORK CONNECTION* 2. Using a Non-PoE Switch If a PoE-enabled switch is not used, use a power adaptor for power transmission and non-PoE switch for d

INSTALLATION* Snapit Easy Installation The Snapit easy installation is a unique Digital Watchdog technology that allows you to install the camera in f

INSTALLATION* 1. Use the camera’s mounting template or your camera to mark the holes as required. 3. Pull wires through and make connections. Use the

INSTALLATION* 5. Mount the camera Surface Mount Base to the wall. 6. Snap the camera module onto the base by aligning the red and black markings on t

INSTALLATION* 8. Adjust the camera’s position by using the 3-Axis Gimbal. 9. Check the LED light. Green light flickers for booting. Red light turns o

INSTALLATION* 1. Verify all parts are in the box. Wall Mount for V4 Housing 2. Run cables into the mount. 3. Use the mounting template to make pilot h

INSTALLATION* 1. Verify all parts are in the box. Ceiling Mount for V4 Housing 2. Attach the top shield to the pendant mount. 3. Run all necessary c

S t o ra g e D e v i c e T h e M V 4 2 1 M e g a p i x e l C a m e r a s o f f e r t h e o p t i o n o f l o c a l e m e r g e n

ADJUSTING THE 3-AXIS GIMBAL* The Gimbal mechanism yields maximum rotation and placement as shown below. Do not over rotate the lens. Doing so will d

I n s t a l l in g I P F i n d e r S o f t w a r e IP Finder searches for all the available Digital Watchdog devices currently connected to yo

2 PRECAUTIONS  Do not open or modify.  Do not open the case except during maintenance and installation, for it may be dangerous and can cause damag

U s i n g I P F i n d e r S o f t w a r e Use IP Finder to change the basic settings of your MEGAPIX camera or to connect to your MEGAPIX ca

U s i n g I P F i n d e r S o f t w a r e Use IP Finder to set the connection type and the IP address information for your MEGAPIX camera.

D H C P The Dynamic Host Configuration Protocol (DHCP) is a network configuration protocol that allows a device to configure automatically accordin

R e s e t t i n g t h e C a m e r a Pressing the reset button on the camera’s control board for five (5) seconds will initialize all environmental

R e m o t e V i d e o M o n i t o r i n g V i a I n t e r n e t E x p l o r e r Monitor and configure the MEGAPIX camera through a built-in Web

R e m o t e V i d e o M o n i t o r i n g V i a C h r o m e , F i r e f o x , o r S a f a r i You can view your MEGAPIX camera using web brow

D i s p l a y S c r e e n > F i r s t S t r e a m & S e c on d S t r e a m Configure two stream settings for monitoring and recording

D i s p l a y S c r e e n > E x p o r t I m a g e E x p o r t a s c r e e n s h o t o f c u r r e n t l i v e v i d e o t o y

D i s p l a y S c r e e n > P r i n t I m a g e P r i n t a s c r e e n s h o t o f t h e c u r r e n t l i v e v i d e o .

D i s p l a y S c r e e n > R e c o r d I n s t a n t l y r e c o r d l i v e v i d e o t o y o u r l o c a l d r i v e . To S

TABLE OF CONTENTS* Introduction...

D i s p l a y S c r e e n > R e c o r d I n s t a n t l y r e c o r d l i v e v i d e o t o y o u r l o c a l d r i v e . To S

D i s p l a y S c r e e n > S e t u p > V i d e o & A u d i o > S t r e a m S e t t i n g s The Recommended Stream Settings

D i s p l a y S c r e e n > S e t u p > V i d e o & A u d i o > C o l o r S e t t i ng s Initially, the factory default se

D i s p l a y S c r e e n > S e t u p > V i d e o & A u d i o > C o l o r S e t t i n g s Initially, the factory default s

D i s p l a y S c r e e n > S e t u p > V i d e o & A u d i o > A u d i o WEBVIEWER* • Connect speaker/microphone wires (not

D i s p l a y S c r e e n > S e t u p > V i d e o & A u d i o > P r i v a c y Z o n e The MV421 MEGAPIX camera offers up to

D i s p l a y S c r e e n > S e t u p > E v e nt > M o t i o n D e t e c t i o n The Motion detection feature allows t

D i s p l a y S c r e e n > S e t u p > E v e n t > M o t i o n A r e a The Motion detection feature allows the MEGAPIX camera

D i s p l a y S c r e e n > S e t u p > E v e nt > S e n s o r S e t t i n g s To Use Sensor 1. Sensor: Select sensor type(NO/N

D i s p l a y S c r e e n > S e t u p > E v e nt > E m e r g e n cy A l a r m Send alarm triggered information to predefined desti

 ONVIF Support (V1.02)  Local SDHC Card Backup  Sony ½.8” CMOS Sensor  Highest Resolution 2.1 Megapixels  1080P (1920x1080) at 30fps  4x Auto-F

D i s p l a y S c r e e n > S e t u p > N e t w o r k > N e t w o r k S e t t i n g s 1. IP Mode: Select the type of IP address

D i s p l a y S c r e e n > S e t u p > N e t w o r k > D y n a m i c D N S If you do not use a public IP address, DDNS provides yo

D i s p l a y S c r e e n > S e t u p > N e t w o r k > C o m m u n i c a t i o n P r o t o co l Current Protocol displays the cur

D i s p l a y S c r e e n > S e t u p > N e t w o r k > A c ce ss P e r m i s s i o n Use the Access Permission page to allow or b

D i s p l a y S c r e e n > S e t u p > N e t w o rk > O n V I F OnVIF is the Open Network Video Interface Forum. 1. To use OnVIF,

D i s p l a y S c r e e n > S e t u p > R e c o r d > S t o r a ge D e v i c e Device Information 1. Click the icon Load Device I

D i s p l a y S c r e e n > S e t u p > R e c o r d > S c h ed u le WEBVIEWER* The recording schedule applies to the SD card local

WEBVIEWER* D i s p l a y S c r e e n > S e t u p > R e c o r d > S c h ed u le WEBVIEWER* The recording schedule applies to the

D i s p l a y S c r e e n > S e t u p > R e m o t e B a c k u p T a b The MD421 MEGAPIX Series allows you to backup your SD card loca

D i s p l a y S c r e e n > S e t u p > S y s t e m > U p g r a d e Upgrade the MEGAPIX camera with an upgrade file. 1. System Ve

The following items are included with the MEGAPIXEL Camera: 5 INSIDE THE BOX* 1. Quick Start Guide 2. 4 Screws & 4 Dry Wall Anchors 3. Secondary V

D i s p l a y S c r e e n > S e t u p > S y s t e m > D a t e & T i m e Set date and time information. 1. Insert the Date

D i s p l a y S c r e e n > S e t u p > S y s t e m > E - m a il N o t i f i c a t i o n Send an e-mail notification when an event

D i s p l a y S c r e e n > S e t u p > S y s t e m > U s e r A c c e ss C o n t r o l To add a new user: 1. Enter Username and

D i s p l a y S c r e e n > S e t u p > S y s t e m > S y s t e m I n f o r m a t io n System Information will display all the cu

D i s p l a y S c r e e n > S e t u p > S y s t e m > L o g s V i e w User can view detailed logs for system and/or events trigger

D i s p l a y S c r e e n > S e t u p > S y s t e m > F a c t o r y D e f a ul t When you select Factory Default, a dialogue bo

IMAGE Image Sensor ½.8” CMOS Sensor Total Pixels 2010 (H) X 1109 (V) Minimum Scene Illumination F1.2 (30IRE): 0.5 Lux (Color) F1.2 (30IRE): 0.01 Lux (

NETWORK LAN 802.3 Compliance 10/100 LAN Video Compression Type H.264, MPEG4, MJPEG (Super Fine ~ Low) Resolution 1920X1080 (16:9) ~ 320X240 (4:3) Fram

Before sending your camera for repair, check the following or contact your technical specialist. I c a n ’ t f i n d m y M E G A P I X c a

Before sending your camera for repair, check the following or contact your technical specialist. I c a n ’ t c o n n e c t t o m y M E G A

1. Lens 2. Camera Control Board 3. Bubble 4. Cover Dome 5. Flush Mount Base 6. Surface Mount Plate 7. Assembly Screws a) T20 M4 X16 8. Safety Wire 9.

Before sending your camera for repair, check the following or contact your technical specialist. I c a n ’ t s e e t h e l i v e v i d e o

Before sending your camera for repair, check the following or contact your technical specialist. S e t t i n g t h e I P A d d r e s s f o r

Digital Watchdog (referred to as “the Warrantor”) warrants the Camera against defects in materials or workmanships as follows: Labor: For the initia

There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages (including, without l

5436 W Crenshaw St, Tampa, FL 33634 PH: 866-446-3595 | FAX: 813-888-9262 www.Digital-Watchdog.com [email protected] Technical Support Hours: Mo

7 CAMERA CONTROL BOARD*

DIMENSIONS* 8

NETWORK CONNECTION* Two Options Use a PoE-enabled switch to connect data and power through a single cable and begin viewing and recording images insta